Cisco 100-105 Exam Questions – (Jan-2018 dumps)

Cisco Certified Design Associate 100-105 exam is possible to pass with excellence without spending a huge amount of time and money by getting help of VCE2Pass’s 100-105 Interconnecting Cisco Networking Devices Part 1 exam questions. Our 100-105 exam dumps material consist of practice test software + PDF Q&A booklet. The success is powered by money back guarantee so your investment is safe either you will succeed or will get the money back moreover you can save 25% of total cost by purchasing the both products together.

100-105 exam questions, 100-105 PDF dumps; 100-105 exam dumps:: https://www.dumpsschool.com/100-105-exam-dumps.html (347 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 100-105 Dumps Exam Questions and Answers:

Version: 12.0
Question: 21

At which layer of the OSI model does the protocol that provides the information that is displayed by the show cdp neighbors command operate?

A. application
B. transport
C. network
D. physical
E. data link

Answer: E

Explanation:
CDP is a device discovery protocol that runs over Layer 2 (the data link layer) on all Cisco- manufactured devices (routers, bridges, access servers, and switches) and allows network management applications to discover Cisco devices that are neighbors of already known devices. With CDP, network management applications can learn the device type and the Simple Network Management Protocol (SNMP) agent address of neighboring devices running lower-layer, transparent protocols.
CDP allows devices to share basic configuration information without even configuring any protocol specific information and is enabled by default on all interfaces.
CDP is a Datalink Protocol occurring at Layer 2 of the OSI model.
CDP is not routable and can only go over to directly connected devices.
CDP is enabled, by default, on all Cisco devices. CDP updates are generated as multicasts every 60 seconds with a hold-down period of 180 seconds for a missing neighbor. The no cdp run command globally disables CDP, while the no cdp enable command disables CDP on an interface. Use show cdp neighbors to list out your directly connected Cisco neighboring devices. Adding the detail parameter will display the layer-3 addressing configured on the neighbor.
Reference: http://computernetworkingnotes.com/cisco-devices-administration-and-configuration/cisco-discoveryprotocol.html

Question: 22

Which two characteristics apply to Layer 2 switches? (Choose two.)

A. Increases the number of collision domains
B. Decreases the number of collision domains
C. Implements VLAN
D. Decreases the number of broadcast domains
E. Uses the IP address to make decisions for forwarding data packets

Answer: A, C

Explanation:
Layer 2 switches offer a number of benefits to hubs, such as the use of VLANs and each switch port is in its own separate collision domain, thus eliminating collisions on the segment.

Question: 23

New Updated 100-105 Exam Questions 100-105 PDF dumps 100-105 practice exam dumps: https://www.dumpsschool.com/100-105-exam-dumps.html

Which OSI layer header contains the address of a destination host that is on another network?

A. application
B. session
C. transport
D. network
E. data link
F. physical

Answer: D

Explanation:
Only network address contains this information. To transmit the packets the sender uses network address and datalink address. But the layer 2 address represents just the address of the next hop device on the way to the sender. It is changed on each hop. Network address remains the same.

Question: 24

Which layer of the TCP/IP stack combines the OSI model physical and data link layers?

A. Internet layer
B. transport layer
C. application layer
D. network access layer

Answer: D

Explanation:
The Internet Protocol Suite, TCP/IP, is a suite of protocols used for communication over the internet. The TCP/ IP model was created after the OSI 7 layer model for two major reasons. First, the foundation of the Internet was built using the TCP/IP suite and through the spread of the World Wide Web and Internet, TCP/IP has been preferred. Second, a project researched by the Department of Defense (DOD) consisted of creating the TCP/IP protocols. The DOD’s goal was to bring international standards which could not be met by the OSI model.
Since the DOD was the largest software consumer and they preferred the TCP/IP suite, most vendors used this model rather than the OSI. Below is a side by side comparison of the TCP/IP and OSI models.

Question: 25

Which protocol uses a connection-oriented service to deliver files between end systems?

A. TFTP
B. DNS
C. FTP
D. SNMP
E. RIP

Answer: C

Explanation:
TCP is an example of a connection-oriented protocol. It requires a logical connection to be established between the two processes before data is exchanged. The connection must be maintained during the entire time that communication is taking place, then released afterwards. The process is much like a telephone call, where a virtual circuit is established–the caller must know the person’s telephone number and the phone must be answered–before the message can be delivered.
TCP/IP is also a connection-oriented transport with orderly release. With orderly release, any data remaining in the buffer is sent before the connection is terminated. The release is accomplished in a three-way handshake between client and server processes. The connection-oriented protocols in the OSI protocol suite, on the other hand, do not support orderly release. Applications perform any handshake necessary for ensuring orderly release.
Examples of services that use connection-oriented transport services are telnet, rlogin, and ftp.

Question: 26

Refer to the exhibit.

If the hubs in the graphic were replaced by switches, what would be virtually eliminated?

A. broadcast domains
B. repeater domains
C. Ethernet collisions
D. signal amplification
E. Ethernet broadcasts

Answer: C

Explanation:
Modern wired networks use a network switch to eliminate collisions. By connecting each device directly to a port on the switch, either each port on a switch becomes its own collision domain (in the case of half duplex links) or the possibility of collisions is eliminated entirely in the case of full duplex links.